Download Commodity

Download Commodity

If you have to administrate an insulin shot, make sure you wash your hands and clean the exterior of the insulin bottles with alcohol wipes beforehand. For a unmarried type of insulin injection, pull the same volume of air into the syringe as the book of the insulin dose, and then release the air into the insulin bottle. Pull up the required dose of insulin and yous're set for the injection. If you're mixing 2 types of insulins, pull upwardly air and release it into each corresponding insulin bottle without drawing up any insulin. So draw up the clear insulin, followed by the cloudy insulin.

  1. ane

    Wash your hands thoroughly. Whenever you're going to be treatment medicine and syringes, you need to make sure you wash your easily very well beforehand. Use warm water and soap and scrub the entire surface area of each hand.[i]

    • Use a clean paper towel to dry out your hands. Hand towels can harbor germs and bacteria that will just get your easily dirty once more.

  2. ii

    Wipe the top of the insulin bottle with an alcohol wipe and let it dry completely earlier using. Apply an alcohol wipe to make clean the top of each insulin bottle before you use it. Allow the alcohol air dry out before y'all move on to the adjacent step.[2]

    • Do not ever wipe the booze off or endeavor to dry out it another way, equally this could easily contaminate your insulin bottle.

    Advertisement

  3. 3

    Roll NPH insulin between your hands before use. If you are using NPH insulin, information technology's important that you lot roll the vial between the palms of both of your hands at least 20 times before yous start to apply information technology. This helps mix the insulin so that it tin can exist more effective after information technology is injected in the body.[3]

    • Never shake the vial of NPH insulin, as this can create air bubbles inside the vial that could later brand their way into the syringe.

    Advertisement

  1. 1

    Pull air into the syringe so that information technology equals the amount of insulin you will use. Pull the syringe plunger out then that air enters the within of the syringe. You lot should pull in a volume of air that is equal to the book of insulin yous'll use.[4]

    • For instance, if you volition be administering ten units of insulin, pull up 10 units of air into the syringe.

  2. 2

    Insert the syringe in the insulin canteen and expel the air. Place the insulin bottle on a flat surface and turn the syringe then that the needle is pointing down. Insert the syringe needle into the insulin bottle and push the plunger down so that all of the air is released.[v]

    • Make sure you continue your finger firmly on the plunger during this process so that it does non release until you lot are ready to measure the insulin.

  3. iii

    Plough the bottle upside down and pull the insulin into the syringe. Keeping the syringe firmly in identify, selection up the insulin bottle and plow information technology upside downwards. Release the plunger slowly and draw upwardly the required amount of insulin from the bottle.[6]

    • Then remove the syringe and place the insulin canteen back on the flat surface.

    Advertisement

  1. 1

    Pull air into the syringe equal to the first dose of insulin. Release the syringe plunger so that it pulls air within. You should draw upward the same volume of air as the book of the first kind of insulin dosage.[7]

    • For case, if you need 7 units of NPH and 5 units of Novolog/Humalog, you volition demand to pull in vii units of air for this commencement stride.
    • Think that you should always draw upward articulate insulin (Novolog/Humalog) before cloudy insulin (NPH).

  2. 2

    Identify the syringe into the commencement insulin bottle and release the air. Insert the syringe needle into the first bottle of insulin and push the plunger and then that the air is released into the bottle. And then remove the syringe from the insulin canteen without cartoon upwardly whatsoever insulin.[8]

    • Make sure the bottle of insulin is kept on a flat surface during this whole procedure.

  3. 3

    Repeat the first two steps with the second bottle of insulin. Draw up the same book of air into the syringe that equals the dosage of the second type of insulin. Insert the syringe into the 2nd canteen and expel the air inside by slowly pressing the plunger.[9]

    • Do not draw any of the insulin up into the syringe at this fourth dimension.

  4. 4

    Draw upwards the clear insulin outset. Insert the syringe needle into the superlative of the clear insulin bottle. Plow the bottle upside downwards and pull upwardly the plunger until you get the required dosage of articulate insulin.[ten]

    • Remove the syringe and supersede the insulin canteen on the apartment surface.

  5. 5

    Describe up the cloudy insulin second. Place the syringe needle in the top of the cloudy insulin bottle and turn the bottle upside down. Advisedly pull the plunger back until you take pulled the necessary amount of insulin.

    • Remove the syringe needle and render the insulin canteen to the flat surface.
    • Be careful not to put pressure level on the syringe plunger until you are set up to draw up the second insulin dosage during this step.

    Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

  • When you open a vial of insulin, mark the date on the canteen with a marking. Throw the bottle out 30 days later this date to prevent leaner growth inside of your insulin.

  • Always double-check that you have the right canteen of insulin before drawing up the medication.

  • Double-check your dosage of insulin to make sure yous take exactly the right corporeality. Be as precise as possible.

Advertisement

References

About This Article

Thanks to all authors for creating a page that has been read 17,780 times.

Did this article aid you?